PC Installation of Windows Netscape 1.1
                          for Win31 and Win95

This file contains information on WWW internet connection of a PC
through the math dept ANNEX. Discussed here in email notes are software,
modem issues and setup.

This file last edited 21 Nov 1996.
This file applies to the 1995 OLDKIT only!

================================NetScape==============================
The WIN3 setup for NetScape is automated by three diskettes (1995),
called the OLDKIT. The kit was put together by Steve Adams (581-5507).
The kit is located at fcom.cc.utah.edu:

1995 oldkit:
  lynx ftp://ftp.k12.ut.us/pub/pc/windows/installation_kits/oldkit/
1996 newkit: (not explained here)
  lynx http://www.micro.cc.utah.edu/win16/internet/16kit.html

Also on the 1995 disk set is FTP, TELNET, PMAIL, GOPHER for win3. It
takes 7mb of disk space to install Steve's client kit. See the notes
below on specifics of how to get the files onto PC diskettes.

The 1995 kit works with CISCO servers directly and it can be made to work
with math's ANNEX. See http://www.math.utah.edu/~gustafso/,
for a document on how to install the 1996 kit. The kits can be mixed,
except for WINSOCK, CONNECT and NETSCAPE (which are in matched versions).

All remarks below apply just to the 1995 kit. The remarks about netscape
can be ignored, or applied to the newest release of netscape.

======================================================================

Dear Roger,
The package for your PC is called "Steve's Internet Client Kit".
It is available by FTP from the campus computer center site. It
requires two (2) 1.44mb diskettes, and about 6-7mb of disk space.
Also required is MS Windows 3.1 (Win95 has been tested) and a suitable
modem, 14400 baud or faster.

After installation is complete, the programs are run from Windows.
Here's what you get:

        Trumpet winsock  --- Creates SLIP or PPP connection
                             to annex.math.utah.edu
        Netscape         --- Same as the one you already use
        Telnet           --- Replaces crosstalk and kermit for
                             most purposes.
        Ftp              --- File transfer protocol for moving
                             files or groups of files between the
                             PC and the remote host (solitude).
        News             --- A news reader for all the news groups that
                             you might be reading currently. Uses
                             windows in an essential way, easy to learn.
        Gopher           --- The standby net searcher with separate
                             windows for each site.
        Mail             --- A mail reader for your remote site
                             (solitude) email.
        Ping, Lview, tn3270 --- Other support programs

Operation: Start "oldkit" WINSOCK. Login to the remote site (solitude).
           On success, "bootp" appears on the screen and some info
           about the connection internet addresses.

           Switch to the program manager (winsock stays running)
           and select any one of the above programs, eg, netscape.
           It should run like it does on dept workstations, only
           more slowly, because of the modem connection.

Setup: The scripts that login to solitude and setup mail, news and
       netscape defaults have to be edited by hand. Once you get this
       right, everything should work seamlessly. A head start is to
       get someone's working edits, and write them over the
       top of "Steve's Internet Kit" sources, which are set up for
       the computer center modem pool.

To get the "internet client kit" (Steve's), use this unix command
on a local workstation:

1995 oldkit:
  lynx ftp://ftp.k12.ut.us/pub/pc/windows/installation_kits/oldkit/
1996 newkit:
  lynx http://www.micro.cc.utah.edu/win16/internet/16kit.html


The idea is to download the source disks as files onto solitude, then
transfer the files to PC diskettes in jwb120 (a Dec3100, for example,
using mtools "mcopy" command):

                Fill drive a: of dec3100 with formatted 1.44 and:
                mcopy sourefile a:

The downloading command "D" in lynx (similar in netscape) is applied to
the compressed file(s) at cc.utah.edu. I'll try it out and send you the
info in the next mail message.

-grant
===================================================================
>To: rhorn@math.utah.edu
>Subject: client kit address

Steve's kit is located directly by this unix command (you can also
use netscape to do the same thing):

   lynx ftp://ftp.k12.ut.us/pub/pc/windows/installation_kits/oldkit/

In this directory are files with the same date starting with "setup.exe",
which is the 1.44mb install kit. the program setup.exe is run from windows
to install the kit.

To download a file in lynx, type the letter d and answer the questions.
On a unix machine all you can do is download to a disk file. To exit
lynx use the letter q or type ctrl-C.

There is a single file lower down in the tree, size 2.6 megabytes.
I downloaded it earlier this year and found it was just the other
files stuffed into one archive. Regardless of the dates, the files
are the same, no difference.

After you install the kit, the editing begins. Out of the box it
won't work. After editing, it works very well, you will  like it!

-Grant

The 1996 kit is
        lynx ftp://ftp.cc.utah.edu/pub/pc/windows/installation_kits
It works with CC and ANNEX servers.

===================================================================
trumpwsk.ini:     (1995 OLDKIT)
================================================================
[Trumpet Winsock]
ip=0.0.0.0
netmask=255.255.255.255
gateway=128.110.198.126
dns=128.110.198.2
time=
domain=math.utah.edu
vector=00
mtu=1500
rwin=4096
mss=1460
rtomax=60
ip-buffers=32
slip-enabled=1
slip-port=1
slip-baudrate=57600
slip-handshake=1
slip-compressed=1
dial-option=0
online-check=0
inactivity-timeout=5
slip-timeout=0
slip-redial=0
dial-parity=0
font=Courier,9
use-socks=0
socks-host=0.0.0.0
socks-port=1080
socks-id=
socks-local1=0.0.0.0 0.0.0.0
socks-local2=0.0.0.0 0.0.0.0
socks-local3=0.0.0.0 0.0.0.0
socks-local4=0.0.0.0 0.0.0.0
ppp-enabled=1
ppp-usepap=0
ppp-username=""
ppp-password=""
win-posn=80 105 606 403 96 408 -4 -4 1
trace-options=0
ip-routing=0
registration-check="iqIT&dk"A<`cx&B^"
next-port=1024
pkt-buffers=16
slip-rtsflow=0
slip-logging=0
slip-rcvbuf=8192
slip-sndbuf=8192
no-close-message=0
use-waitmessage=0
clock-period=100

[default vars]
$number=5818105

================================================================
login.cmd
================================================================
output atz\13
input 10 OK\n
repeat
 outputecho "atdt18105"\13
until [input 30 CONNECT]
input 30 sername:
output YOURUSERNAME\13          <=======
input 30 assword:
output YOURPASSWORD\13          <=======
input 30 hangup
input 30 annex:
output ppp\13
bootp

========================================================================
Editing the INI files   (1995 OLDKIT)
========================================================================

        TRUMPWSK.INI
          ip=0.0.0.0
          netmask=255.255.255.255
          gateway=128.110.198.126       (math gateway)
          dns=128.110.198.2             (math name server, DNS)
          domain=math.utah.edu          (math domain default)
          slip-port=1           (for com1; use 2 for com2)
          slip-baudrate=57400   (for 14400 or 28800 modem connection)
          ppp-enabled=1         (enable PPP connection)

        WINVN.INI
          NNTPHost=news.math.utah.edu  (news server)
          NNTPService=mail.k12.ut.us   (mail account site)

        NETSCAPE.INI
          Home Page=http://www.math.utah.edu/
          NNTP_Server=news.math.utah.edu
          SMTP_Server=localhost
          POP_Server=pop.math.utah.edu

Note: There is no hope that any of the windows programs will work unless
      the INI files have been edited.

========================================================================
WINSOCK INITIALIZATION  (1995 Steve's Internet Kit)
   Run windows 3.1
   Run Trumpet Winsock
    Open DIALLER menu
    Select manual login
     Enter
       ATZ
       ATDT5818105              (math number)
       LOGIN                    (your login user name)
       PASSWORD                 (your password)
       ppp                      (after annex lets you in, type "ppp")
       ESC                      (press ESC key)
   Switch to Program Manager in Windows 3.1
   Run PING or NETSCAPE to test.

========================================================================
NETSCAPE OPERATION
   It won't work unless Trumpet Winsock has been initialized
   and Winsock is still running with PPP enabled. A common mistake is to
   switch out of Winsock without hitting the ESC key (which enables
   PPP). The script files can automate this once you get it working.

   The site at the top of the screen should be

                http://www.math.utah.edu/

   The trailing slash is necessary. If you don't have one, then add it
   into the INI file called NETSCAPE.INI. For testing, add it in the
   netscape application and hit return to load the new URL. This works
   also for any other URL, eg,

                http://www.yahoo.com/


========================================================================
KILLING THE PPP CONNECTION
   Don't depend on software like Winsock to kill the modem connection.
   It probably won't kill it. Instead, cycle the power on the modem.
   Doing this will let you exit from Winsock, which refuses to let you
   out when a PPP connection has been made. If you are lucky enough to
   have a "bye.cmd" on the DIALLER menu in Winsock, then use that
   command to shut down the modem (before exit from Winsock). Hint: it
   does not hurt to type ESC in Winsock. Doing that enables menu items
   on the DIALLER menu.

   Note: PPP means "PC-to-PC Protocol", which is SLIP plus another
         software layer that makes connection to remote sites like
         annex.math.utah.edu much more convenient. The extra software
         layer resolves automatically the IP address that is dynamically
         assigned by annex.math.utah.edu (different on each login). This
         gets windows users out of the business of typing IP numbers.

===================================================================
BYE.CMD
===================================================================
#
#  Trumpet Winsock 2.1 Bye.cmd
#
#  Copyright (C) 1994,1995 Peter R. Tattam &
#  Trumpet Software International Pty Ltd (TSI)
#  All rights reserved.
#
#  Unless TSI has given prior written consent to such use,
#  no permission is granted to distribute or otherwise make available
#  to the public modified versions of this script for commercial purposes.
#  Any permitted distribution of modified versions of the script must
#  retain the copyright notice at the start of this file and must clearly
#  identify those parts of the file which have been modified.
#
#
#  Set %which to 1 for normal DTR hang up or
#                2 for ATH0 style hangup
#
%which = 2
#message "Disconnecting modem..."
if %which = 1
  set dtr off
  sleep 1
  set dtr on
end
if %which = 2
  sleep 2
  output +++
  input 5 OK\n
  output ath0\r
  input 5 OK\n
end
#message "Modem has been disconnected."
sleep 1

========================================================================
BYE2.CMD
========================================================================
#
#  Trumpet Winsock 2.1 Bye.cmd
#
#  Copyright (C) 1994,1995 Peter R. Tattam &
#  Trumpet Software International Pty Ltd (TSI)
#  All rights reserved.
#
#  Unless TSI has given prior written consent to such use,
#  no permission is granted to distribute or otherwise make available
#  to the public modified versions of this script for commercial purposes.
#  Any permitted distribution of modified versions of the script must
#  retain the copyright notice at the start of this file and must clearly
#  identify those parts of the file which have been modified.
#
#
#  Set %which to 1 for normal DTR hang up or
#                2 for ATH0 style hangup
#
%which = 2
status "Disconnecting modem..."
if %which = 1
  set dtr off
  sleep 1
  set dtr on
end
if %which = 2
  sleep 2
  output +++
  input 5 OK\n
  output ath0\r
  input 5 OK\n
end
status "Modem has been disconnected."
sleep 1

========================================================================
login.cmd for annex.math.utah.edu
========================================================================
output atz\13
input 10 OK\n
repeat
 outputecho "atdt18105"\13
until [input 30 CONNECT]
if ![load $username]
  if [username "Enter your login username"]
    save $username
  end
end
if ![load $password]
  if [password "Enter your login password"]
    save $password
  end
end
input 30 authorization
input 30 Annex
input 30 sername:
output $username\13
input 30 assword:
output $password\13
input 30 hangup
input 30 annex:
output ppp\13
bootp

NOTE: If this does not work, then try setting SLIP in the SETUP menu.
       Replace "PPP" above by "SLIP DEFAULT" and try again. On a few
       newer modems, especially modem cards, this is the only one that
       works! (works for math and the computer center)

========================================================================
login1.cmd  Another version for off campus
========================================================================
output atz\13
input 10 OK\n
repeat
 outputecho "atdt5818105"\13
until [input 30 CONNECT]
if ![load $username]
  if [username "Enter your login username"]
    save $username
  end
end
if ![load $password]
  if [password "Enter your login password"]
    save $password
  end
end
input 30 authorization
input 30 Annex
input 30 sername:
output $username\13
input 30 assword:
output $password\13
input 30 hangup
input 30 annex:
output ppp\13
bootp
========================================================================
login2.cmd  A very complicated example with more features.
========================================================================
#
#  Trumpet Winsock 2.1 Login.cmd
#
#  Copyright (C) 1994,1995 Peter R. Tattam &
#  Trumpet Software International Pty Ltd (TSI)
#  All rights reserved.
#
#  Unless TSI has given prior written consent to such use,
#  no permission is granted to distribute or otherwise make available
#  to the public modified versions of this script for commercial purposes.
#  Any permitted distribution of modified versions of the script must
#  retain the copyright notice at the start of this file and must clearly
#  identify those parts of the file which have been modified.
#
#trace on
#
# set up some strings for dialling up
#
if ![load $number]
  if [query $number "Enter your dial up phone number"]
    save $number
  end
end
if ![load $username]
  if [username "Enter your login username"]
    save $username
  end
end
if ![load $password]
  if [password "Enter your login password"]
    save $password
  end
end
$modemsetup = "&c1&k3"
$prompt = ">"
$userprompt = "sername:"
$passprompt = "assword:"
$slipcmd = "slip"
$addrtarg = "our address is"
$pppcmd = "ppp"
$pppready = "PPP."
%attempts = 10

###############################################
# timeouts for various sections of the script #
###############################################
#
# timeout for busy tone... adjust this until the BUSY string is detected.
#
%busytimeout = 10
#
# time between successive busy attempts.
#
%busywait = 30
#
# time to wait for a CONNECT string to be received
#
%connecttimeout = 60
#
# time to wait until DCD is detected
#
%onlinetimeout = 60
#
# time to wait for username & password prompts
#
%logintimeout = 60
#
# time to wait for server prompt to appear
#
%prompttimeout = 30
#
# time to wait for a SLIP address to be parsed
#
%addresstimeout = 30
#
#
#
#
#----------------------------------------------------------
#
# initialize modem
#
status "Initializing modem..."
output "atz"\13
if ! [input 5 OK\n]
  message "Modem is not responding"
  abort
end
#
# setup our modem commands
#
output "at"$modemsetup\13
if ! [input 10 OK\n]
  message "Modem is not responding"
  abort
end
#
# send phone number
#
%n = 0
repeat
  %n = %n + 1
  if %n > %attempts
    message "Too many dial attempts"
    abort
  end
  status Dialling $number...(attempt %n)
  output "atdt"$number\13
  %busy = [input %busytimeout BUSY]
  if %busy
    status "The line is busy...pausing for a while"
    sleep %busywait
    %ok = 0
  else
    %ok = [input %connecttimeout CONNECT]
  end
until %ok
input 10 \n
#
#  wait till it's safe to send because some modem's hang up
#  if you transmit during the connection phase
#
wait %onlinetimeout dcd
status Connected.  Now logging in as $username...
#
# now prod the terminal server
#
#output \13
#
#  wait for the username prompt
#
input %logintimeout $userprompt
output $username\13
#
# and the password
#
input %logintimeout $passprompt
output $password\13
#
# we are now logged in
#
status "Logged in. Now switching to Internet..."
input %prompttimeout $prompt
if %ppp
  #
  # jump into ppp mode
  #
  output $pppcmd\13
  #
  # wait for PPP prompt.
  input %prompttimeout $pppready
  #
  display \n\n"PPP mode selected.  Will try to negotiate IP address."\n
  status "PPP mode selected.  Will try to negotiate IP address."
  sleep 1
  #
else
  #
  # jump into slip mode
  #
  output $slipcmd\13
  #
  # wait for the address string
  #
  input %addresstimeout $addrtarg
  #
  # parse address
  #
  address 30
  input %addresstimeout \n
  #
  # we are now connected, logged in and in slip mode.
  #
  display \n
  display Connected.  Your IP address is \i.\n
  status Connected.  Your IP address is \i.
  sleep 1
end
#
# now we are finished.
#
========================================================================
setup.cmd       Not needed
========================================================================
if [query $number "Enter your phone number"]
  save $number
end
if [query $username "Enter your login username"]
    save $username
end
if [query $password "Enter your login password"]
    save $password
end

========================================================================
setup2.cmd  Not needed
========================================================================
#
#  Trumpet Winsock 2.1 Setup.cmd
#
#  Copyright (C) 1994,1995 Peter R. Tattam &
#  Trumpet Software International Pty Ltd (TSI)
#  All rights reserved.
#
#  Unless TSI has given prior written consent to such use,
#  no permission is granted to distribute or otherwise make available
#  to the public modified versions of this script for commercial purposes.
#  Any permitted distribution of modified versions of the script must
#  retain the copyright notice at the start of this file and must clearly
#  identify those parts of the file which have been modified.
#
%ok = [load $number]
%ok = [load $password]
%ok = [load $username]

if [query $number "Enter your phone number"]
  save $number
else
  exit
end
if [username "Enter your login username"]
  save $username
else
  exit
end
if [password "Enter your login password"]
  save $password
else
  exit
end
========================================================================
End of CMD files from cmds.zip
========================================================================